tag:blogger.com,1999:blog-6539093728798325673.post1968715570194971871..comments2018-07-19T18:29:39.437-07:00Comments on CubeX 3D Printing Blog: Simplify3D settings for the CubeX PrintercubeX-3D-printmanhttp://www.blogger.com/profile/16386814853378553046noreply@blogger.comBlogger4125tag:blogger.com,1999:blog-6539093728798325673.post-32335004445970659292017-02-08T00:44:25.421-08:002017-02-08T00:44:25.421-08:00Hi!
I have recently laid my hands on a CubeX singl...Hi!<br />I have recently laid my hands on a CubeX single.<br /><br />I correctly installed your profile and was trying some stuff but an issue occurred:<br /><br />1) I adjusted the z-axis offset to match my bed level (I find it easy to fine tune it this way, rather than hardware setting on the machine)<br />2) To increase adhesion I lowered the first layer speed to 50%<br />3) Since some edges kept bending (PLA, no heated plate) I googled and turned off the fan for the first layer, configuring 2 set point for fan control: layer 1: fan speed 0 and layer 2: fan speed 60 (it was already set at 60)<br /><br />So that is my configuration, but after the first layer, when the fans kicked on the printer seemed to freeze. It was proceeding in the printing time and the temperature was kept at 190, but nothing moved. When I aborted the print... it did not move (usually it goes back on top of the waste material box)<br /><br />I ended up shutting it off and on again.<br /><br />Any thoughts? <br />Mobyhttps://www.blogger.com/profile/14546735013385274197noreply@blogger.comtag:blogger.com,1999:blog-6539093728798325673.post-76193120350028331002017-01-31T18:07:51.122-08:002017-01-31T18:07:51.122-08:00I was able to get simplify3d working thanks to you...I was able to get simplify3d working thanks to your guide so thank you! I also have the grm heatbed installed but it hasnt been heating up all the way ever since i started using simplify3d. I know the controller isnt connected to the grm controller so it isnt simplify3d fault. Could you send me the setting of your grm controller? like the advanced setting when you hold the set key? i went through the auber syl manual but im not sure if their default settings are the same as grm sends it with. Im not sure what settings to look for so if you could tell me all 25 of them i would really appreciate it! Anonymoushttps://www.blogger.com/profile/07825061369928011399noreply@blogger.comtag:blogger.com,1999:blog-6539093728798325673.post-20710596037660432612017-01-24T23:37:35.834-08:002017-01-24T23:37:35.834-08:00I tried your Cubex duo file and version 3.1.1 but ...I tried your Cubex duo file and version 3.1.1 but it is asking for .frm file instead. When i load the .fff file it seems to load fine but it only saves in .gcode instead of .bfb. Any Suggestions would be much appreciated!Anonymoushttps://www.blogger.com/profile/07825061369928011399noreply@blogger.comtag:blogger.com,1999:blog-6539093728798325673.post-89964414913848262842017-01-10T13:19:00.793-08:002017-01-10T13:19:00.793-08:00Hello, thank you for sharing all this very value i...Hello, thank you for sharing all this very value information. Thanks to you I'm finally confident on the printing quality of this machine. Please post some pictures of your parts using simplify3D.Anonymousnoreply@blogger.com